Hot mix asphalt · tons for a compacted thickness

Asphalt calculator

Enter length, width and the compacted thickness to calculate hot mix asphalt in cubic yards and US tons. The preset is Iowa DOT’s 145 lb/ft³ for estimating quantities, compacted in place; highway agencies publish 145–151 lb/ft³.

145 lb/ft³ compacted preset108.75 lb per yd² per inchLaid ≈ 25% thicker, rolled down

Measure the area to cover

Area 1

Hot mix asphalt, compacted · agency reference · 145 lb/ft³ · 0% extra. No compaction adjustment.

Material & allowance Edit

Iowa DOT’s 145 lb/ft³ for estimating hot mix asphalt quantities, compacted in place. Enter the compacted thickness, not the loose depth the paver lays. Source: Iowa DOT. No automatic compaction factor. Weights & sources.

Bag sizes & cost Optional

Use a supplier quote. Taxes, labor and compaction are not added automatically.

How much asphalt you need

LengthWidthDepth

Enter your dimensions to see cubic yards, tons and bags

Start with an example

The short answer

How much asphalt do I need?

A 12 × 40 ft driveway, 3 in over a gravel base needs 120 ft³, or 4.44 cubic yards, which is about 8.7 US tons at the Iowa DOT figure of 3,915 lb per cubic yard (1.96 tons per yard). Enter the thickness after rolling. Leave the extra allowance at zero for rolldown; set one only for waste or uneven ground.

Thickness

How thick should an asphalt driveway be?

State asphalt pavement associations publish minimum designs. Either the whole depth is asphalt (full depth), or a thinner layer sits on compacted aggregate. All figures are compacted inches.

Minimum designs as two state asphalt associations publish them
UseDesignSource
Driveway, good or fair subgrade4.5 in full depth, or 3 in over 4 in aggregateColorado Asphalt Pavement Association
Driveway, poor subgrade5.5 in full depth, or 3 in over 6 in aggregateColorado Asphalt Pavement Association
Driveway4 in may be adequate; 5–6 in full depth is stronger; or 3 in over 6–8 in compacted aggregateIllinois Asphalt Pavement Association
Parking lot, light duty5 in full depth, or 6 in aggregate + 2.5 in asphalt base + 1.5 in surfaceIllinois Asphalt Pavement Association

Weak or wet soil needs the thicker design. For the aggregate layer, use the road base calculator; for a gravel driveway instead of asphalt, the gravel driveway calculator.

The calculation

How to calculate asphalt

  1. Measure the area and take the compacted thickness.Length × width in feet, then the finished thickness in inches from the plan. Paving thicknesses are always stated after rolling.
  2. Multiply by a compacted density.Highway agencies estimate hot mix at 145–151 lb/ft³ in place. Cubic feet × density ÷ 2,000 gives US tons.
  3. Or use a spread rate.Paving crews quote pounds per square yard per inch: 108.75 at 145 lb/ft³. Square yards × inches × that rate ÷ 2,000 is the same tonnage.
  4. Do not add a loose allowance.The paver lays the mat about 25% thicker and the rollers bring it down, but the tonnage is the same. Ordering by the compacted thickness already accounts for it.

Rectangle · US measurements

Length × Width × Depth ÷ 324

Feet × feet × inches → cubic yards

Cubic yards × 3,915 ÷ 2,000

Cubic yards × lb/yd³ → US tons at the reference weight

Read the full calculation method ↗

Worked examples

Asphalt calculator examples

At 145 lb/ft³, before any allowance. Open one to load it into the calculator.

Quantities at the supplier reference
ProjectVolumeWeight
12 × 40 ft driveway, 3 in over a gravel base120 ft³ · 4.44 yd³8.7 US tons
12 × 40 ft driveway, 4 in full depth160 ft³ · 5.93 yd³11.6 US tons
60 × 90 ft parking lot, 5 in full depth2,250 ft³ · 83.33 yd³163.13 US tons

Bulk quantities

How much does a ton or a cubic yard of asphalt cover?

One US ton at 3,915 lb per cubic yard is 0.51 cubic yards (13.79 ft³).

At 3,915 lb per cubic yard, compacted
DepthOne US ton coversTons for 100 ft²
1.5 in
parking lot surface layer, IAPA
110.34 ft²0.91 tons
3 in
driveway over aggregate base, CAPA
55.17 ft²1.81 tons
4 in
full-depth driveway, IAPA minimum
41.38 ft²2.42 tons
5 in
full-depth parking lot, IAPA
33.1 ft²3.02 tons
Cross-section of one US ton of asphalt at 3,915 pounds per cubic yard spread at 1.5, 3, 4, 5 inches deep: at 1.5 inches it covers about 110 square feet, and at 5 inches about 33 square feet, so the deeper layer covers less ground.
Each layer is the same US ton of asphalt; its width is the area covered at that depth.

Why the density matters

How much does a yard of asphalt weigh?

One cubic yard of asphalt weighs 3,915 to 4,077 lb (1.96 to 2.04 US tons) across the published figures below, and 3,915 lb (1.96 US tons) at the calculator’s preset.

Weight per cubic yard as published by Iowa DOT, R.J. Valente, FHWA Central Federal Lands, Michigan DOT, Asphalt Institute and Alaska DOT&PF
ProductPublisherlb per yd³Tons per yd³
Hot mix asphalt, for estimating quantitiesIowa DOT3,9151.96
Hot mix asphalt, producer's calculator defaultR.J. Valente3,9151.96
Hot asphalt mix, for estimatingFHWA Central Federal Lands3,918.921.96
HMA application rate, 1 inchMichigan DOT3,9601.98
Hot mix asphalt, surface and intermediate courseIowa DOT3,9691.98
Asphalt mixture, in placeAsphalt Institute3,9962
Hot mix asphalt, Type IV, Class BAlaska DOT&PF4,0232.01
Hot mix asphalt, Type II, Class AAlaska DOT&PF4,0772.04

Enter your supplier’s figure under Material & allowance. These are compacted, in-place weights from highway agencies, the Asphalt Institute and a producer. They are not comparable with the loose figures for gravel on the gravel density reference.

Spread rate

Asphalt tons per 1,000 square feet

Paving estimates use pounds per square yard per inch. Michigan DOT and the Asphalt Institute both work with 110; the preset here gives 108.75.

US tons for 1,000 ft² at each compacted thickness
Compacted thicknessAt 108.75 lb/yd²·inAt 110 lb/yd²·in
2 in12.08 tons12.22 tons
3 in18.13 tons18.33 tons
4 in24.17 tons24.44 tons

Loose versus compacted

Rolldown: how thick the paver lays it

Hot mix leaves the paver at about 70–80% of its maximum density (Michigan DOT), and the rollers take it to at least 92%, preferably 93–94% (FHWA). The mat is laid thicker to allow for it.

Thickness to lay for a compacted thickness, at the handbook’s 25% rolldown for dense-graded mix
CompactedLaid by the paver
1.5 in1.88 in
2 in2.5 in
3 in3.75 in
4 in5 in

How thick each lift can be

The Asphalt Institute sets the minimum at three times the nominal maximum aggregate size. TxDOT publishes limits by mix:

Compacted lift thickness by mix, from TxDOT’s Pavement Manual
MixNominal max. sizeLift, min–max
SP-D3/8 in1.25–2 in
SP-C / TY-D1/2 in1.5–3 in
TY-C3/4 in2–4 in

Small repairs

Bagged cold patch for potholes

For a pothole, bagged cold patch is sold by coverage rather than by the ton. Fill in layers and tamp each one.

Cold patch coverage as the makers state it
ProductBagStated coverageBags for 4 ft² at 2 in
QUIKRETE Asphalt Cold Patch50 lbabout 0.5 ft³ compacted; about 6 ft² at 1 in2
SealMaster PatchMaster50 lbabout 5 ft² at 1 in, 2.5 ft² at 2 in2

Before you order

Frequently asked questions about asphalt

How much does asphalt weigh per cubic foot?

Between 145 and 151 lb compacted, in the agency and producer figures on this page. The Asphalt Institute gives 142 to 148 lb/ft³ in place and says to use 148 for estimates.

How many tons of asphalt do I need for a 12 × 40 ft driveway?

About 8.7 US tons at 3 inches and 11.6 tons at 4 inches full depth, at 145 lb/ft³. The gravel base under a 3 inch driveway is a separate order; see the road base calculator.

How much thicker is asphalt before it is rolled?

About 25% for a dense-graded mix and 15% for gap- or open-graded mixes, according to the Asphalt Paving Handbook: a 2 inch compacted lift goes down 2.5 inches thick.

How thick can one layer of asphalt be?

At least three times the mix’s nominal maximum aggregate size, says the Asphalt Institute, and lifts are generally limited to 6 or 8 inches. With static steel-wheeled rollers alone, 3 inches is the most that compacts properly.

How many bags of cold patch fill a pothole?

A 4 ft² pothole 2 inches deep takes 2 bags of QUIKRETE Asphalt Cold Patch, which covers about 6 ft² at 1 inch per 50 lb bag, or 2 of SealMaster PatchMaster at 5 ft².

For suppliers and site owners

Add this asphalt calculator to your website

Selling or delivering asphalt? Let customers work out how much to order before they call for a quote. Paste the snippet below into any page; the calculator loads from Site Measure with the same preset as this page, needs no maintenance and stays free. A credit link is appreciated but optional; you may mark it nofollow or remove it.

Open it on your own figures (optional)

Leave these blank to use this page’s sourced preset. The figures are stored in the snippet itself; Site Measure keeps no account or record of them.

The frame is 760px tall and fills the width of its container. Preview the widget, or contact us if you need metric units or another change.

References

  1. Hot mix asphalt, for estimating quantities: 145 lb/ft³, Iowa DOT. Recorded November 11, 2026
  2. Hot mix asphalt, producer's calculator default: 145 lb/ft³, R.J. Valente. Recorded November 11, 2026
  3. Hot asphalt mix, for estimating: 2,325 kg/m³, FHWA Central Federal Lands. Recorded November 11, 2026
  4. HMA application rate, 1 inch: 110 lb/yd² per inch, Michigan DOT. Recorded November 11, 2026
  5. Hot mix asphalt, surface and intermediate course: 147 lb/ft³, Iowa DOT. Recorded November 11, 2026
  6. Asphalt mixture, in place: 148 lb/ft³, Asphalt Institute. Recorded November 11, 2026
  7. Hot mix asphalt, Type IV, Class B: 149 lb/ft³, Alaska DOT&PF. Recorded November 11, 2026
  8. Hot mix asphalt, Type II, Class A: 151 lb/ft³, Alaska DOT&PF. Recorded November 11, 2026
  9. Asphalt Driveways technical brief (March 2020), Colorado Asphalt Pavement Association
  10. Driveways, Illinois Asphalt Pavement Association
  11. Parking lots, Illinois Asphalt Pavement Association
  12. What is the recommended minimum lift thickness for placing HMA?, Asphalt Institute
  13. Five handy rules of thumb for pavement construction, Asphalt Institute, Asphalt magazine
  14. 7.5 Layer thickness, Asphalt Paving Handbook (NAPA-hosted)
  15. Construction Manual, 501 Plant Produced Hot Mix Asphalt, Michigan DOT
  16. Tech Brief FHWA-HIF-21-020: Density Demonstration Projects and Related Specifications, FHWA
  17. Pavement Manual, Placement Considerations, Table 6-3, TxDOT
  18. Asphalt Cold Patch No. 1701-58 data sheet, QUIKRETE
  19. PatchMaster Pothole Patch specification sheet, SealMaster

About these calculations

Every figure on this page links to its source; recorded dates are shown with the figures or in the gravel weight and price ledgers, and the arithmetic is covered by automated tests. The 145 lb/ft³ preset is Iowa DOT’s Design Manual figure for estimating hot mix asphalt quantities, compacted. This page estimates material only; it is not a pavement design. How we source and calculate · Report an error